InspectAPedia ^TM

Blueray Heating Boiler or Furnace Safety Recall Notice
HeatAPedia ^©

	Enter your search terms Submit search form
	Search This Website - InspectAPedia.com

This document contains the recall notice for unsafe Blueray heating equipment, and continues to add additional history, technical details, and photographs to aid consumers and home inspectors in identifying this equipment. Blueray blueflame furnaces and boilers have been recalled by the US CPSC as unsafe equipment which can cause fatal carbon monoxide poisoning.

In an earlier, now obsolete notice, the U.S. Consumer Product Safety Commission, in October 1987, warned that lack of proper maintenance of Blueray "Blue Flame" furnaces or boilers could lead to carbon monoxide poisoning. Blueray Systems, Inc. of Schuylkill Haven, Pa., issued an alert to oil heat technicians, distributors, and to homeowners of the importance of careful maintenance of the units. © Copyright 2008 Daniel Friedman, All Rights Reserved. Information Accuracy & Bias Pledge is at below-left. Use the links at page left to navigate this document or to go to Other Website Topics. Green links at left show where you are in our document & website. Our site offers impartial, unbiased advice without conflicts of interest. We will block advertisements which we discover or readers inform us are associated with bad business practices, false-advertising, or junk science. Our contact info is at inspect-ny.com/appointment.htm.

Blueray Safety Recall Notice from CPSC

CPSC Warns of Potential For Carbon Monoxide Poisoning Involving Blueray "BLUE FLAME" Furnaces And Boilers

WASHINGTON, DC -- In voluntary cooperation with the U.S. Consumer Product Safety Commission, Blueray Systems, Inc., of Schuylkill Haven, Pennsylvania, has initiated a program to alert oil heat service technicians, oil heat distributors and home owners of the importance of strict service and maintenance of the Blueray "blue flame" furnace or boiler. A total of nearly 21,000 of such furnaces and 14,500 boilers were produced between 1974 and 1983.

According to the Commission, since 1979 there have been seven deaths from carbon monoxide poisonings that have been linked to improper maintenance or servicing of the Blueray "blue flame" furnaces or boilers.

The firm is working through oil heat distributors and organizations servicing these distributors, to notify all persons living in homes where these furnaces have been installed, Consumers are being reminded that annual maintenance of the equipment is necessary for safety and efficiency. The need for this specialized maintenance is due to the design of the equipment for high-efficiency heating which requires annual servicing. Each household is also being supplied with a label to permanently attach to the furnace/boiler which alerts the home owner and the servicer of the necessity for strict adherence to all service and maintenance procedures prescribed by the firm.

Consumers can determine if their furnace/boiler is one involved in this alert program by looking for a blue and white label on the equipment which reads "BLUERAY by Blueray Systems, Inc." The model number, BR 60/75, appears on a white label. Consumers having these furnaces should immediately contact Blueray Systems, Inc., to receive their free safety label, as well as copies of publications which describe the proper procedures for maintenance and service. Blueray can be reached by calling collect on 215-789-6224 or by writing to: Blueray Systems, Inc., 8301 Lansdowne Avenue, Upper Darby, Pa 19082.

To report unsafe consumer products or to receive safety information, call the CPSC toll-free hotline number at 800-638-CPSC. A teletypewriter number for the hearing impaired is 800-638-8270.

The US CPSC included this identifying sketch and list of model numbers of the recalled Blueray heating equipment.

Additional Data about Blueray Heating Equipment

During the U.S. heating oil shortage in the 1970's many heating companies began marketing "high efficiency" heating equipment to allow homeowners to save on heating oil costs. One model, the Blueray boiler, marketed by Blueray systems, the "blue flame" boiler (or furnace) was particularly tricky to tune. In adjusting the air mixture one had to follow a very precise procedure specified by the manufacturer. If the procedure was not followed in the right order, even though the ending system setup appeared the same and test measurements appeared proper, the system would produce carbon monoxide - a potentially lethal hazard. Heating technicians didn't necessarily know that it made a difference to adjust to the proper combustion air mixture by coming up from lean to rich rather than from rich to lean.

By 1979 at least seven people had died from carbon monoxide poisoning (I believe deaths occurred on Long Island, in New York), A safety recall notice was issued by the U.S. CPSC.

In a move that seemed too little too late, a special safety warning label was provided by Blueray. I include that safety warning label image here in the off chance that it may help readers identify a Blueray or "Blue Ray" Blue Flame heating boiler or furnace.

The Thermodynamics Boiler Company's Version of Blueray or Blue Ray Blue Flame Heating Equipment

Later models of the Blueray heating boiler (Blueray furnaces were also manufactured) attempted to correct these safety concerns but the company did not survive its image as dangerous.

The Thermodynamics Boiler Company purchased the remains of the defunct "Blueray Systems", redesigned the heating equipment, and marketed it under several names which included the "Blueray" appellation. Those service people "in the know" realized that the Thermodynamics version of Blueray was a different animal and did not have the same safety concerns as the original.

But many home inspectors and home owners saw only the "Blueray" label and immediately called for replacement, even if it was a "Thermodynamics" Blueray heater.

Most Blueray's are now long gone from most homes as they were steel boilers most of which have by now rusted out of service, regardless of which model. But occasionally you may come across one of these which has been preserved in use. If the boiler is a Blueray manufactured by Blueray Systems, it is dangerous and should not be used.

List of Blueray Model Numbers Recalled

These model numbers appeared on a white label such as the Blueray label shown above.

• Blueray Model # BR-60 was recalled by the US CPSC
• Blueray Model # BR-75 was recalled by the US CPSC
• Blueray Model # BRL-75 was recalled by the US CPSC
• Blueray Model # BFH-60 was recalled by the US CPSC
• Blueray Model # BFH-75 was recalled by the US CPSC
• Blueray Model # CBF-60 was recalled by the US CPSC
• Blueray Model # CBF-75 was recalled by the US CPSC
• Blueray Model # HBF-60 was recalled by the US CPSC
• Blueray Model # HBF-75 was recalled by the US CPSC

More Details about Blueray Heating Boilers and Furnaces and the Safety Recall

The following was a consumer handout which we provided to home inspection and heating system clients from 1975 to present.

CPSC Original Warning Issued on Blueray Boilers

The notice which follows is obsolete - this equipment has since been recalled. This information is provided below for technical research only.

The U.S. Consumer Product Safety Commission, in October 1987, warned that lack of proper maintenance of Blueray "Blue Flame" furnaces or boilers could lead to carbon monoxide poisoning. Blueray Systems, Inc. of Schuylkill Haven, Pa., issued an alert to oil heat technicians, distributors, and to homeowners of the importance of careful maintenance of the units. Even if the model number of your system is different from the specific ones for which the warning was issued you should have your service person check this system for proper operation promptly. The check itself should be an inexpensive service call.

Annual Service Important

The CPSC reminds consumers that annual maintenance of these units is necessary. The units can be identified by a blue and white label reading "Blueray by Blueray Systems Inc." The model number BR 60-75 appears on a white label.

Long Island home-heating industry sources said the more complex Blue Flame system requires special adjustment equipment. It also employs a more sensitive fuel consumption method more likely to produce the deadly gas if regular maintenance is ignored. According to CPSC seven deaths from carbon monoxide poisoning have been linked to poor maintenance of these systems. Blueray sold 21,000 of these systems between 1974 and 1983.

Consumers who have these furnaces or boilers can obtain additional information by calling Blueray collect at 215/789-6224 or by writing Blueray Systems Inc., 8301 Lansdowne Ave., Upper Darby, PA., 19082. Sources: Nassau County Office of Consumer Affairs, reported in Newsday, 10/30/87; Blueray Systems, Inc. Safety Notice letter indicates that copies of Blueray's Operation, Maintenance and Installation Procedures, its Technical Training Guide, and its recent Field Service Bulletin may be obtained free of charged by calling Blueray Collect at 800/338-9681.

Blueray Field Service Bulletin Notes

Service departments receiving calls from Blueray owners complaining of odors and/or pulsation should instruct homeowners to turn the emergency switch off until a serviceman arrives.

Hand held carbon monoxide analyzer should show no measurable carbon monoxide in the flue gases. (CO2 should read 12.5-13.5%). The bulletin offers added detail for assuring that measurements and adjustments are done properly.

When setting the unit for proper air mixture always start with the air band fully open, close it until proper CO2 reading is reached. Close it further - if CO2 continues to climb you are on the "right side of the curve" and should then re-open the air band to proper CO2 reading. If it does not continue to climb you are on the "wrong side of the curve" in air-starved mode and are producing carbon monoxide (CO).

The unit should not be operated until corrective steps have been taken and there is no measurable CO in the stack.

Blue Ray or Blueray Safety Warning Update (January 2007)

OPINION: the following comments are provided in response to correspondence from some readers who have observed that the original US CPSC warnings regarding this equipment are difficult to locate at the US CPSC website:

It is possible the US Government has decided to remove some of its product safety recall information (regarding Blueray Heating Systems) from the market, either because of the age of the issue and the relatively few original BlueRay heaters which remain in use or perhaps for other more obscure reasons such as industry pressure - after all, a dangerous boiler is bad press for the heating equipment industry and the heating fuel folks too.

The reason we have the listed data such as model numbers (see above) is that we have been tracking this issue and keeping all of the information that was originally released.

Heating service technicians don't want to service your BlueRay furnace or boiler, if it's one of the problem ones (originals) because they know about the hazards and don't want the responsibility of touching a system that is tricky to tune, has a dangerous reputation, and is vulnerable to modification by an untrained person after the heating service technician has left the site.

In use of the words "recall" versus "safety warning" it is possible that in our original description (and repetition of the original text) a "CPSC Product Recall" was never put into effect, and instead, a safety warning was issued. For example, it is possible that the CPSC and companies involved agreed that the two CPSC consumer warning notices were sufficient.

When Blueray systems were in widespread use, people working in the heating industry as independent service and repair contractors were in agreement that the boiler had to be replaced, or had to be serviced and adjusted ONLY by someone who was well trained and who followed the service procedure precisely.

A real fear among heating service people is that even if they do precise and correct work, nothing prevents a homeowner or someone else from coming along after them and changing a setting or component to make the system unsafe. The additional level of care needed and the risk of a possible fatality was enough to cause most service people to refuse to service the boiler at all, and to call for its replacement.

Building owners who have one of the original Blueray boilers or furnaces installed (which should be rare given their present age) should replace the boiler. For ethical reasons however, we can't however, recommend a specific replacement brand of heating boiler or furnace.

Other Blueray Boiler Service Notes and Contact Information

For information about Blueray systems more than 5 years old contact Blueray Corporation, 1/800-338-9681. (Jim Salls is one of the engineers there.)

For information about more recent Blueray Systems, for example the VTF models made by Thermodynamics Corp. contact that company at 717/385-0745. (John Minchoff is one of the engineers there.) These newer boilers are referred to in the trade as having a "yellow flame" burner rather than the "blue flame" units mentioned above, and generally use burners provided by Beckett(TM).

According to the CPSC's compliance officer consumers can also try contacting Thermo-Dynamics Boiler Company (Blueray or Blue Ray Blue Flame Heating Equipment) Rob Glinskas, Route 61 - P.O. Box 325, Schuylkill Haven, PA 17972, Phone: (570) 385-0731, Fax: (570) 385-5304, http://www.thermodynamicsboiler.com/ [Email T/D Potts to DJF 9/29/2006]

On some Blueray VTF models we've found (Daniel Friedman) sooting and burnout or burn marks inside jacket covers (not always visible without disassembling the system). This problem may be caused by loss of an internal cap seal at top of the fire chamber and may be evident only if the system is run dirty or improperly adjusted so as to have positive backpressure in the fire chamber. It can be checked for by removing covers during service. Repair, provided the fire chamber is not damaged, should not involve significant expense, but can be important for fire safety.

How to Identify, Reset, or Adjust Hot Water Heating Boiler or Steam Boiler Controls and Switches

For details about the controls, components and switches commonly found on hot water heating systems see the articles listed below in which we explain how to identify, set, re-set, repair, replace, or avoid problems with the components of a hot water heating system. Use links just below or at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

• Hot Water Heating Boiler Operating Details - 39 Steps to Hot Water Heating Success
• Air Bleeder Valves for Hot Water Heating Systems: Radiators, Baseboards, Convectors
• Aquastats Heating Boiler Primary Controls: A guide to Aquastats for control of hot water heating boilers and tankless coils
• Cad Cell Relays on oil fired furnaces or boilers as flame sensors & safety devices
• Check Valves Guide to check valves and backflow preventers on hydronic (hot water) heating systems (gas or oil fired)
• Circulator Pumps Guide to circulator pumps and circulator relays on hydronic (hot water) heating systems (gas or oil fired)
• Draft Hoods on gas fired heating equipment, function and safety
• Draft Regulators & barometric dampers on oil fired heating equipment
• Electrical Power Switches: Where to Turn On or Off Heaters for Furnaces & Boilers, Heat Pumps or Electric Furnaces or Air Conditioners
• Expansion Tanks Guide to pressure control and expansion tanks on hydronic (hot water) heating systems (gas or oil fired)
• Flue Gas Spill Switch on gas fired heating equipment sense combustion and protect from blocked flues
• Gas Piping, Valves, Controls: Guide to LP and natural gas meters, valves, tanks, piping, gas leaks, gas regulator assembly & other gas controls
• Gauges for Temperature & Pressure: Guide Temperature & Pressure Gauges on Hot Water or Steam Heating Boilers
• Low Water Cutoff Controls: Guide to LWCOs on hot water heating systems
• Mixing Valves: Guide to mixing valves on hot water heating systems and radiant heat systems
• Oil Burners: Guide to Oil Burners for heating systems, boilers & Furnaces: basic parts, operation, maintenance, performance & money-saving tips
• Oil Tanks: Guide to Heating Oil Underground & Above ground Oil Storage Tank Leaks, Testing, Problems & Solutions, Home Buyer's / Home Owner's Guide
• Oil Piping: A guide to heating oil piping, valves, controls, leaks, repairs for heating systems
• Parts & Components Guide for Heating Boilers: How to Identify the Components of Hot Water Heating Boilers - A Guide to Hydronic Heating System Parts
• Relief Valves - TP Valves: A guide to temperature and pressure relief valves & safety controls on hot water and steam heating systems
• Stack Relay Switches: Guide to finding, resetting, maintaining stack relays on oil fired furnaces or boilers as flame sensors & safety devices
• Tankless Coils: A Guide to tankless coils used to produce domestic hot water on heating boilers: hot water quantity, safety, temperature control, leaks, corrosion, repairs
• Thermostats & Heat Controls for furnaces & boilers, oil & gas fired, heat pumps or electric furnaces or boilers
• Water Feed Valves: A guide to water-feeding/pressure-reducing valves on hot water and steam heating systems
• Zone Valves: A guide to zone valves for heating zone control on hot water heating systems

More expert information on this topic

More Information on Building Diagnostic Inspections and Repairs

• Heating System Defects & Inspection Methods

InspectAPedia ^TM Home & Site Map - Building Inspection, Diagnosis, & Repair, Environmental Inspection & Testing - Research Website

The Mold Information Center: What to Do About Mold in Buildings, When and How to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems

Use this simple, economical mold test kit by following our instructions on how to collect and mail mold samples to our lab

Environmental Inspection, Testing, & Diagnosis On-Site IAQ, Gas, Air Testing, Mold Investigation, Sick Building Diagnosis, Lab Services, & Remediation Plan Preparation - indoor air quality testing, problem source determination, supporting lab work, written remediation plan addressing removal of environmental and other hazards and prevention of their recurrence.

Home Inspection Construction Consulting Services & advice for home buyers

Contact Daniel Friedman for website content suggestions or for fee-paid consulting

	Enter your search termsSubmit search form
	Search This Website - InspectAPedia.com