InspectAPedia TM
Building & Environmental Inspection, Testing, Diagnosis, Repair, & Problem Prevention Advice Home
Conditioning
Inspection
Ventilate
Inspect/Test
Water
Septic
Directory of Professionals to Inspect or Test a Building
InspectAPedia TM Building & Environmental Inspection, Testing, Diagnosis, Repair, & Problem Prevention Advice |
||||||||||||||||||||||||||
| InspectAPedia Home |
| | Air Conditioning |
| | Electrical | | | Environment | | | Exteriors | | | Heating | | | Home Inspection |
| | Insulate Ventilate |
| | Interiors | | | Mold Inspect/Test |
| | Plumbing Water Septic |
| | Roofing | | | Structure | | | Contact Us |
| Directory of Professionals to Inspect or Test a Building |
||||||||||||||||||||||||||
 Mobile View HEATING SYSTEMS ANTI SCALD VALVES BOILERS, HEATING BOILER OPERATION DETAILS BOILER CONTROLS & SWITCHES Air Bleeder Valves Aquastat Functions BOILER LEAKS CORROSION STAINS BOILER OPERATING PROBLEMS BOILER PARTS LIST Cad Cell Relay Switch Flame Sensors Circulator Pumps & Relays Expansion Tanks Limit Switches Mixing Valves Relief Valves - TP Valves Spill Switches Stack Relay Switch Zone Valves CARBON MONOXIDE/DIOXIDE CARBON MONOXIDE WARNING CHIMNEY INSPECTIONS CHIMNEYS & Flues - Asbestos Transite Pipe DRAFT HOODS - gas fired DRAFT REGULATORS - barometric dampers DUCT SYSTEMS DUCT INSULATION, Asbestos Paper DUCTS, Asbestos Transite Pipe DUST FROM HVAC? ELECTRICAL POWER SWITCH FOR HEAT FURNACES DUCT SYSTEM DEFECTS FAN LIMIT SWITCH FURNACE CONTROLS & SWITCHES FURNACE OPERATION DETAILS HEAT EXCHANGER LEAKS STACK RELAY SWITCHES GAS PIPING, VALVES, CONTROLS GAUGES ON HEATING EQUIPMENT HEAT LOSS INDICATORS HEATING COST SAVINGS HEATING LOSS DIAGNOSIS-BOILERS HEATING LOSS DIAGNOSIS-FURNACES HEATING OIL CLOUD WAX GEL POINT HEATING OIL SLUDGE HEATING SYSTEM INSPECTION DIAGNOSIS REPAIR HEATING INSPECTION CONCEPTS HEATING INSPECTION PROCEDURE INSULATION MIXING VALVES NO HEAT - BOILER / FURNACE DIAGNOSIS OIL BURNERS OIL BURNER NOISE SMOKE ODORS OIL FUEL TYPES & CHARACTERISTICS OIL TANK LEAKS OIL TANK SLUDGE OIL TANKS, BURIED PLASTIC HEATER VENT RADIANT HEAT Floor Mistakes to Avoid RELIEF VALVES - TP Valves Safety Recalls BLUERAY Recall CHIMNEYS & Flues - Asbestos Transite Goodman HTPV RECALL Lennox WARNING Weil McLain RECALL SAFETY DURING HEATING INSPECTION SPILL SWITCHES - Flue Gas Detection STAIN DIAGNOSIS on Indoor Surfaces STEAM HEATING SYSTEMS Cad Cell Relay Switch Flame Sensors Mixing Valves Relief Valves - TP Valves Sight Glass, Steam Boiler Pressure Switch, Steam Boiler Spill Switches Stack Relay Switch Steam Vents LOW WATER CUTOFF CONTROLS WATER FEEDER VALVES TANKLESS COILS THERMAL TRACKING THERMOSTATS Transite Pipe Chimneys & Flues ZONE VALVES More Information InspectAPedia TM Home & Site Map Air Conditioning InspectAPedia Bookstore Electrical Environment Exteriors Heating Home Inspection Insulate Ventilate Interiors Mold Inspect/Test Plumbing Water Septic Roofing Structure Accuracy & Bias Pledge Contact Us |
A Guide to Cad Cell Relay Switches on Oil Burners
|
Flame sensing devices on oil-fired heating appliances: modern oil-fired heating furnaces, boilers, and water heaters use a Cadmium Cell sensor, usually located inside the oil burner tube, to "see" the presence of flame and thus to assure that the oil burner assembly stops pumping oil into the combustion chamber if flame ignition is unsuccessful. The cad cell itself, that is the little cell that "sees" the oil burner flame, is wired (often by a yellow wire) to the cad cell relay switch (see photo) which is ususally a gray box with a red "reset" button located on top of or alongside the the oil burner assembly. The cad cell causes the relay to switche the oil burner off when a flame is not established or if flame is lost at the oil burner (or inside the furnace or boiler's combustion chamber). Our photograph shows a modern Honeywell(R) R8184G 4009 cad cell relay for use on (typical) intermittent ignition oil burner equipment. This device is likely to be found on oil burners less tan 15 years old, and on both hot air furnaces and hot water boiler heating systems provided that they are heated by an oil burner. |
How to Reset the Oil Burner Cad Cell Relay: The photograph tells alot about this oil burner and heating system. The debris on top of the cad cell relay contacts (pointed to by our ruler) indicates that the system is running dirty and perhaps with a puff-back at startup or with backpressure in the combustion chamber. Look closely at the mostly-covered gray cover of this Honeywell cad cell relay control. In the upper center of the photo you can just see a hole in the top of the cover. This is where we should have seen a red cad cell relay button. But the button itself, a plastic part affixed to the cover top, has broken away. We can still reset this cad cell relay however, by removing the cover and looking inside for the button which is mounted on the relay circuit board itself. That button is the actual relay switch and it can still be pressed to reset the switch if needed, even if the external button has been lost. If the red "reset" button on the cad cell relay is sticking up and the oil burner has shut down, the homeowner is permitted to try ONCE to "reset" the system by pressing the red reset button. If the oil burner does not turn on and run normally and continuously (no smoke, no loud noises, etc.) for at least 5 or 10 minutes after resetting the relay or pressing the reset button, DO NOT keep resetting the system since doing so can flood the combustion chamber with un-burned heating oil - a dangerous condition. The photograph shows an older Honeywell cad cell relay swtich - the gray box in the right in this illustration. If the cad cell has told the relay that it can't see any flame, the cad cell relay switch will have turned off electrical power to the oil burner and the red button will have popped up. |
Testing cad cell relays: is possible by simply pressing the red button down when the oil burner is operating. If the oil burner is operating normally and you press the cad cell relay reset button donwn it should turn off the oil burner. When you release the button the oil burner should re-start. This test checks the interrupt circuit in the relay. We recommend not trying this test unless the oil burner has been on for a few minutes or more (and has had time to warm up) so that we don't produce unnecessary sooting in the combustion chamber during stop and start of the burner.
Cleaning or replacing an oil burner cad cell is pretty easy, but this is a job for the service technician since it's necessary to turn off power to the oil burner and partly disassemble the oil burner to access the cad cell sensor. Often by removing a lock screw or two, the voltage transformer (the black box atop[ the oil burner in this photo) is simply hinged back and one can see the yellow wire entering the oil burner tube and leading to the cad cell sensor. The cad cell relay sensor will be mounted in a little bracket and positioned where it can "see" the flame when the oil burner is operating.
If the oil burner has not been operating properly, say has been producing too much smoke and soot, even after it has been adjusted it may be necessary to inspect and clean soot from the cad cell sensor so that it has a non-sooty clear view of the flame. Or the technician, if s/he has any doubt about the sensor, will simply replace it. It's a simple plug-in part (two pins on the sensor plug into a receptacle that is secured by a bracket inside of the oil burner tube).
Particular thanks are due to experts and also consumers who read these articles and suggest corrections, changes, and additions to the material. Content suggestions, technical corrections and content critique are invited for any of the content at our website.
More expert information on this topic
InspectAPedia TM Home & Site Map - Building Inspection, Diagnosis, & Repair, Environmental Inspection & Testing - Research Website
The Mold Information Center: What to Do About Mold in Buildings, When and How
to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems
Home Inspection Construction Consulting Services & advice for home buyers
Contact Daniel Friedman for website content suggestions or for fee-paid consulting
| Advertise on This Website → |
04/10/2008 - 09/05/06 http://www.inspect-ny.com/heat/CadCellRelaySwitch.htm © Copyright Dan Friedman 2008-1999 All Rights Reserved
