InspectAPedia ^TM

Home Buyer's Basic Guide to Septic Systems - Step-By-Step Inspection & Testing Advice for Buying a Home With a Septic Tank

	Enter your search terms Submit search form
	Search This Website - InspectAPedia.com

• Advice for people buying a home with a septic system, septic tank, drainfields
• What inspections and tests should be performed on septic systems when buying a home?

Advice for Home Buyers who are buying a property with a private septic system. This document offers basic advice on evaluating the condition of an on-site private sewage disposal system, evaluation of various "test" methods, sources of information specific to a given property, and general outline of how a typical septic system functions and what are its components. If you don't really want to know much about septic systems but you want to know how to inspect and test this costly and buried system when you're buying a property with a septic system, septic tank, septic fields, then read this document - the "Septic Buyers Basic Step by Step Guide". For a thorough explanation of what to do when buying a home with a septic tank and leachfield, see our :Complete Guide To Buying a Home with a Septic System.

That document expands on septic dye testing, probing, and board of health research. If you want to become a bit of a septic system expert, still more details of exactly how septic dye testing is performed, how septic tanks are maintained, pumped, and inspected, the use of septic additives, blocked drain and septic system failure diagnosis, and septic system design for typical as well as difficult sites, see our main septic information page: The Septic System Information Website. © Copyright 2008 Daniel Friedman, All Rights Reserved. Information Accuracy & Bias Pledge is at below-left. Use links at the left of each page to navigate this document or to view other topics at this website. Green links show where you are in our document or website.

Purpose of This Advice on Buying a House with a Septic System

Frequently prospective buyers of a single family home have many questions regarding the septic system serving the dwelling: What does the existing septic system consist of? Is it working property? What septic inspections and tests should I have performed when I am buying a home? How long will a septic system last? In order to help buyers obtain Information that addresses these concerns. We have put together this Fact Sheet to guide them in making informed decisions regarding the potential problems and costs associated with a property's septic system.

Components of a Septic System

In simplest terms, a septic system consists of a holding tank which retains solid waste and grease from household waste water, and an absorption system or "leach field" which disposes of liquid wastewater or "effluent" which leaves the septic tank for absorption below ground into soils at the property.

How to Inspect and Test a Septic System When Buying A Home

This document gives a simple overview of the questions to ask and tests and inspections to order if you are buying a property with a septic system. If you need to know more about septic system components, septic system maintenance (such as tank pumping and septic additives), or details about septic system inspection, diagnosis, repair, and alternative septic designs, Our main septic website page provides in-depth articles about these topics.

Why inspect and test a septic system before buying a home?

The septic system is a relatively expensive and buried system which does not have an infinite life. Eventually drain fields fail and sometimes septic tanks, especially steel ones, rust out and need replacement. Also, old septic tanks, cesspools, and drywells, especially site-built or "home made" systems and systems in certain soils, can collapse, forming a very dangerous site hazard.

While no septic inspection and test can guarantee 100% that all septic defects have been found, properly conducted, these procedures can reduce the chances of a dangerous or costly surprise at your new home.

Septic Inspection and Testing for Home Buyers, Step-by-Step

You can do steps 1 and 2 yourself. If you hire an expert to inspect and test the system (some home inspectors can provide this service), the inspector will also perform step 2 and 3.

1. Basic Questions:Ask the seller the following questions. Don't worry if the seller says they don't know the answers. "Not knowing" is also important information. These questions are deliberately a bit vague in order to allow people to tell you whatever they know rather than cutting off or suggesting answers. Convey the answers to these questions to your septic test consultant.
• How old is the property?
• Is the property occupied or vacant? If occupied, for how long and by how many occupants? If vacant, for how long?
• How long has the seller owned the property?
• Where is the septic system?
• What is installed?
• What is the service or repair history of the septic system?
• When was the tank last pumped? [Warning: if the seller offers to "have the tank pumped for you" ask them not to do you that favor before your inspection as pumping the tank prevents testing the drain field.]
2. Visual Inspection: Make a visual inspection of the property. Look for wet areas, smelly areas, rocky areas, areas of recent excavation. Also make note of the location of and distance to nearby streams, private wells, ponds, buildings, property lines, and rocky areas, and areas of trees and shrubbery. [Warning: be very alert for evidence of sink holes or subsidence. Do not walk over anything suspicious as you might step into or fall into a collapsing system.]
3. Septic Loading & Dye Test: Hire a septic test consultant to perform a septic loading and dye test. This procedure puts a test volume of water into the system to look for evidence of a blocked pipe or for breakout of septic effluent at the yard surface - indications of the need for repair. If you are looking at a completely new home and septic system you might omit this test but don't assume that new systems are immune to failures. Pipes settle and break or systems can be improperly installed. If the tank was pumped immediately before your inspection you should be suspicious, and you might defer the loading and dye test as it may be unable to put enough water into the system to test the drain fields. The dye itself is just a coloring agent to identify water that may appear at the yard surface. It's the test volume of water that's important.
4. Pump and inspect the septic tank: this step may or may not be necessary, depending on the age and service history of the system and the results of the visual inspection and loading and dye test. Important additional information, available when the tank is pumped, can tell you if it was past-due for pumping (risking damaging the drain fields) and if it is damaged. You'll also know exactly where the tank is, if it's concrete, steel, fiberglass or home made, if it has been damaged, and if it has a save cover.

Additional steps which are not normally done but which may be performed if there is evidence of system damage or failure are listed next. These steps would ordinarily be performed by a septic contractor who installs or repairs septic systems. Some septic pumping companies also perform septic repairs and field investigations. A septic engineer may be needed if you are expanding a system or if you require design to repair a system on a difficult site.

• Find and Open the Distribution Box which connects the pipe from the tank to the network of drainfield lines.
• Excavate suspicious areas such as wet areas at in the leach field, subsidence areas.
• Perform soil percolation tests or "Perc tests" to evaluate the ability of the soils to absorb effluent. This involves digging a hole, pouring in water, and measuring the time for a given volume of water to be absorbed into a given square foot area of soil.
• Soil & Site Research to include determination of the soil quality, the depth of the seasonal high water table in the ground below the leach area, etc. - this work may be needed if a system is to be replaced or relocated, especially at a difficult site.

More Reading about Septic System Inspection and Testing

More basic information about how septic systems work is in this document after this section. More in-depth information about the steps in the procedure outlined above can be read at the following online articles:

• Directory of Professional Inspectors available via Internet (Some of these inspectors offer septic system testing and inspection)
  
  
• Diagnosing Clogged Drains: A First Step for Homeowners
• Performing a Septic Loading and Dye Test - How to perform this test (separate document)
• Septic Tank Pumping Guide: When, Why, How to pump the septic tank
• Table of Required Septic Tank Sizes: Septic Tank Capacity vs Usage in Daily Gallons of Wastewater Flow & How to Calculate the Size (in gallons) of a Septic Tank.
• How Big Should the Leach Field Be? - table of soil percolation rate vs. field size
• Home & Outdoor Living Water Requirements
• Table of Required Clearances: Distances Between Septic System & Wells, Streams, Trees, etc.
• Septic System Inspection Methods and Procedures, - online illustrated class for building and septic inspectors
• Septic Systems Inspection, Testing, & Maintenance- online textbook. Detailed how to inspect, maintain, repair information
• The Septic System Information Website our main web page for this topic

For a leaching system to function properly it must:

1. Provide enough application area. The application area is the amount of surface area of soil within the leaching system where sewage effluent is applied (referred to as "wetted" area). The amount of application area needed for a given house depends on the characteristics of the soils on the property and the daily flows (in gallons) generated from the house.
2. Be surrounded by natural soil conditions which will be able to dissipate and disperse the discharge without becoming over saturated.
3. Provide enough capacity to store effluent during periods of unusually heavy use or when rainfall or subsurface flooding reduces the ability of the system to disperse the liquid. Note: Curtain drains or ground water interceptor drains are sometimes installed upgrade of the leaching system to minimize high ground water conditions.

It is important to realize that, once a septic system has been installed, only one of the above factors can be controlled by the homeowner. The homeowner can control how much water is actually being discharged to the system. Since each system has a set maximum capacity, it behooves the homeowner not to exceed that amount.

Signs of Trouble With the Septic System

If a system starts to experience difficulties, what are some of the common symptoms?

1. Plumbing fixtures may exhibit difficulty in releasing their contents (slow draining, bubbling, backups, etc.). This condition may be system-related but it could also indicate just a clog in the interior piping or sewer line. You should have the interior piping checked before proceeding with an investigation of the sewage disposal system. [DJF added: See Diagnosing Clogged Drains: A First Step for Homeowners]
2. Large volume discharges (such as, washing machines, dishwashers and bathtubs) cause either a backup, as noted above, or, an overflow of sewage above the septic tank or leaching field. If this condition is usually at its worst during and/or directly following a heavy rain event, then the septic system is indeed suspect. If backup alone occurs independent of wet weather, you might first check for a partial blockage of the main drain that has occurred some distance from the house. In such cases a small discharge will simply be held by the main waste pipe, draining slowly past the blockage, while a large discharge will cause a backup.
3. Foul septic odors in storm drainage piping, catch basins, footing drain piping or curtain drain discharges may indicate that sewage from your property or an adjacent one is entering these ground water systems.

Sources of Information about your particular septic system

What can a prospective purchaser of a home do to gather as much information as possible relative to the present condition of a system and about possible future expenses associated with the septic system? Here are a few suggestions:

Obtain Information about the septic system from the present property owner

• Ask for any drawings regarding the actual location (an "as-built drawing) of the existing septic system.
• Ask for the records regarding maintenance of the system; Has the septic tank been pumped at a frequency of at least 3 to 5 years?; What pumping contractor was used?; If the system contains a pump. how often has it been maintained?; If major repairs have been made, when and to what extent?
• Ask about the past performance of the system. Have any of the symptoms described earlier manifested during the life of the system?

Make a Visual Site Inspection of Septic System Condition at the Property

• Once the locations of the septic tank and leaching fields are known, walk over the entire area and observe whether there is any evidence of a sewage overflow condition. Greener grass in the leaching area may not necessarily indicate a system problem. If, however the area is completely saturated and odorous you should be very concerned. It most likely indicates an active failure.
• Try to get a sense of how natural conditions are effecting the capacity of the property to disperse water. Is the sewage disposal area located In a depression which would have a tendency to collect run-off of rain water? Is the lot flat? Is there a water course of wetland (swamp) near the leaching system? Is the system virtually at the same elevation as nearby wetlands? Are there steep slopes and/or ledge outcrops which reduce the available area for leaching purposes? All of the above factors could indicate that the existing system will experience difficulty or, that there may not be much additional area suitable for sewage disposal on the lot if needed in the future.
• [DJF addition: Also see Table of Required Septic & Well Clearances: Distances Between Septic System & Wells, Streams, Trees, etc.]

Go to Town Health Department to Review the Property's Septic System Information File

• Ask the town sanitarian to review the file with you. Is there enough information in it for him/her to give you an opinion on how the existing system and/or lot meets present health code requirements?
• Ask for the records regarding maintenance of the system; Has the septic tank been pumped at a frequency of at least 3 to 5 years? What pumping contractor was used? If the system contains a pump, how often has it been maintained?; If major repairs have been made, when and to what extent?
• Your goal is to, confirm and supplement information received from the property owner.
• Obtain guidelines concerning the proper maintenance of a subsurface sewage disposal system.
• If you are contemplating an addition to the home or plan on renovating an unfinished basement discuss the possibilities with the sanitarian and determine the procedures you would have to follow to accomplish your plans. In wm cases it will not be possible to "enlarge" an existing home.
• Ask about the general neighborhood, the frequency of repairs, ability to install proper size repair systems, average life of systems in the area, etc.

Obtain Additional Information from Outside Sources

• Presently many home sales are contingent upon a home Inspection. Part of the inspection usually includes a test of the existing septic system. [Note: Septic Tests are beyond the scope of a professional home inspection but are offered as an additional for-fee service by most home inspectors who serve areas where private systems are common.] Unfortunately many of the people performing these tests do not have a complete understanding of how a systems function and may perform only a perfunctory test such as a low-water volume or using an insufficient amount of tracer dye. Therefore, the conclusions reached from these tests are often misleading. Be sure your test is performed by an expert.

  Three common septic tests performed during home inspections are:

1. The Septic Loading and Dye Test (properly a "septic loading and dye test) is used to trace the movement of septic tank effluent into the leaching system. The theory is that if the dye "surfaces" to the ground or appears in a brook or catch basin the system is in trouble. Although this is indeed true, the opposite result does not necessarily mean the system is - functioning or will function properly In the future. In order for the dye to appear it must flow through the septic tank and leaching fields prior to arriving at the breakout point. This usually would take a large amount of water and sufficient time to occur, and most home Inspections do not last long enough to fulfill this requirement.

   [DJF note: This opinion of the Health Department is not entirely accurate. National data collected among professional home inspectors between 1985 and 1995 indicated that a significant number of inspectors performing dye tests discovered total failure of the septic system within 20 to 30 minutes of beginning testing. We agree that a dye test is by no means a complete test of a system, that the other measures suggested here are extremely valuable, and that the volume of water used is critical: too little or too much can both be serious mistakes. If a wet area or soggy area is present, dye has been found to appear in the short time indicated. However beware: NYS DEC has found dye appearing in nearby streams as late as five days following a septic dye test in cases where effluent migrates through considerable ground area before entering a stream. See Performing a Septic Loading and Dye Test - How to perform this test (separate document)]

2. Probe Test is a procedure whereby the Inspector attempts to locate the "key" elements of the system (septic tanks and leach fields) and determine if they are experiencing hydraulic distress (meaning the septic tank and fields are flooded). This test is basically inaccurate since it only takes a single "snapshot the condition of the system. It may be a "good" day for the system (very little water was used by the homeowner that day; the house may have been empty for some time; it may be the middle of the summer when soil conditions are at their best and a judgment is being made with very little long term information.

   [DJF notes: WARNING: probing can damage buried equipment such as fiberglass septic tanks or tank covers or plastic septic drain lines. Further, there is little assurance that the probing is done in the area where a problem is present.]

3. The flooding "test" is actually the process of discharging a vast amount of water into the existing system. Depending on the number of fixtures utilized, an additional 500 to 1,000 gallons of water can enter the ' system during the course of an Inspection.

   The inspector then examines the leaching area to observe any signs of an "overflow condition." If none is noted, it is assumed the system is functioning property. This type of test is most disturbing since it can actually do harm to the system by "artificially" flooding the septic tank and fields. This could lead to suspended solids escaping the tank, causing increased clogging to the leaching fields. Also, the results of such a test can be misleading in that the prior use of the system (both over and under utilization) will have a direct bearing on the outcome of the "test."

   [DJF note: the opinion of CT DOH that an inspector injects 500 to 1,000 gallons of water contradicts the earlier DOH opinion that held that it is impossible to inject significant volumes of water into a system during a typical 3 hour home inspection. It is easy to place 200 to 500 gallons into a septic system during a three to four hour home inspection. 1000 gallons would be a bit high. Even if a high available water flow rate in a building makes it possible to place very large volumes of water into a private septic system, we advise against attempting flooding tests (very large volumes) as in cases where the type of septic system is unknown it is possible to damage or even destroy the system leading to very costly and previously unnecessary repairs. A test which greatly exceeds the design parameters of the system is a questionable procedure. The Septic Information Website describes appropriate procedures for performing various septic tests based on a national survey of inspection and engineering practices.]

• Use of Soil Conservation Service County Soil Maps (through the town sanitarian), try to identify the type of soil most likely present on the site in order to predict the feasibility of future repairs to the existing leaching system.
• Talk to neighbors about the general performance of septic systems In the area and specifically the system on the property you're Interested In. However, this is suggested only for those comfortable approaching this subject with strangers and with the realization that the information gathered may not be totally factual for various reasons (devaluation of their own property; not wanting to spoil the sale of a friendly neighbor, etc.)
• Hire your own septic test consultant either a professional engineer [who is specifically familiar with septic system design and repair], an inspector who has experience with and is familiar with septic loading and dye testing standards, a licensed septic inspector (in states which license this specialty such as MA), or a licensed septic system installer, who performs a great deal of work in the particular town. They can give you advise as to the condition of the soils and septic systems In the area and what might be expected (especially pertaining to costs) if/when you find problems with the existing system.
[DF addition: After performing the septic loading and dye test and obtaining whatever historical maintenance and repair information you can obtain from the prior owner, depending on the septic system condition and when it was last pumped, you may want a septic contractor to located, open, pump, and inspect the septic tank. More details about this step are at Performing a Septic Loading and Dye Test,Septic System Inspection Methods and Procedures, and
• Septic Tank Pumping Guide: When, Why, How to pump the septic tank.]
• Obtain water meter readings (if the home is serviced by a municipal water supply) to determine what the present occupants of the home are utilizing. Then compare those results with what your family is presently using. If your family Is using significantly more water than the former occupants you may be asking for trouble if the sewage system is undersized by today's standards.
• Additional useful information which may be available from the service company who has pumped the tank recently includes the following:
  • Type of tank material - old steel tank may be at or end useful life
  • Tank size - along with usage determines appropriate pumping frequency and system capacity
  • Evidence of damage to tank components - broken baffles mean the leach fields are probably ruined
  • Evidence of backflow into the tank during start of pumping - indicates flooded leach field, probably failed
  • High sludge level and/or excessive floating scum level - indicate high risk of having pushed solids out into the leach field, destroying it
  If the system has not been cleaned in several years and if the seller will permit, have the tank pumped to obtain this additional information. Typical pumpout fees are around $100. if excavation is not necessary. If the tank location is unknown extra costs will be involved to locate and excavate it - steps to which a seller is likely to object.

Home Buyers' Guide to Septic Systems - A Final Overview

State of Connecticut Department of Health Services
150 Washington St., Hartford CT 06106
203-566-1292 Voice 203-566-2275 Fax

More Information on Septic System Testing, Diagnosis, Repair, Maintenance, Design, & Alternatives

• The Septic System Information Website
• Connecticut Department of Public Health & Addiction Services
• Directory of Professional Inspectors available via Internet (Some of these inspectors offer septic system testing and inspection)
  
  
• Diagnosing Clogged Drains: A First Step for Homeowners
• Performing a Septic Loading and Dye Test - How to perform this test (separate document)
• Septic Tank Pumping Guide: When, Why, How to pump the septic tank
• Table of Required Septic Tank Sizes: Septic Tank Capacity vs Usage in Daily Gallons of Wastewater Flow & How to Calculate the Size (in gallons) of a Septic Tank.
• How Big Should the Leach Field Be? - table of soil percolation rate vs. field size
• Home & Outdoor Living Water Requirements
• Table of Required Clearances: Distances Between Septic System & Wells, Streams, Trees, etc.
• Septic System Inspection Methods and Procedures, - online illustrated class for building and septic inspectors
• Septic Systems Inspection, Testing, & Maintenance- online textbook. Detailed how to inspect, maintain, repair information

InspectAPedia ^TM Home & Site Map - Building Inspection, Diagnosis, & Repair, Environmental Inspection & Testing - Research Website

The Mold Information Center: What to Do About Mold in Buildings, When and How to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems

Home Inspection Construction Consulting Services & advice for home buyers

Use this simple, economical mold test kit by following our instructions on how to collect and mail mold samples to our lab

Environmental Inspection, Testing, & Diagnosis On-Site IAQ, Gas, Air Testing, Mold Investigation, Sick Building Diagnosis, Lab Services, & Remediation Plan Preparation - indoor air quality testing, problem source determination, supporting lab work, written remediation plan addressing removal of environmental and other hazards and prevention of their recurrence.

Contact Daniel Friedman for website content suggestions or for fee-paid consulting

	Enter your search termsSubmit search form
	Search This Website - InspectAPedia.com