InspectAPedia ^TM

Testing for Lead Contamination in Water WaterAPedia © Enter your search terms Submit search form   Search This Website - InspectAPedia.com Tests for Lead Contamination in Water When to test water for lead contamination Water test choices & alternatives Costs & of various water tests

What drinking water contamination tests should you order? Here we discuss the general classes of water contaminants covered in a water test for lead. There are several possible sources of lead in drinking water, including lead in ground water, lead contamination from municipal water piping, lead contamination from building water supply piping or fixtures, well contamination by lead from surface contamination due to lead paint chips, and insignificant lead contamination from lead in well pumps or faucet parts. This website describes the types of water testing available, outlines common water test fees, describes the details of what parameters are included in various water test options, and gives advice to assist you in deciding what tests to order. Readers should also see our longer article Water Quality Testing, and advice for home buyers and building owners: water contaminants, water test procedures, well shock procedures, preventing drinking water contamination, and Cheating on water tests in that document. © 2008 Daniel Friedman, All Rights Reserved. Information Accuracy & Bias Pledge is at below-left. Use the links at page left to navigate this document or to go to Other Website Topics. Green links at left show where you are in our document & website.

Lead Contamination from Water Supply Lines/Entry Mains, Lead Testing & Correcting Contamination from - Lead Pipe Problems/Advice

Depending on the duration and extent of lead-water contact, lead can enter the water supply if lead is present in supply piping or fixtures. Common sources of lead in water supply piping include older lead-bearing solder used on copper pipes, possible lead content in brass piping or fixtures, lead water supply piping (rare), and lead water supply entry main between a building and the public water main in the street (common in some areas). Readers of this article must also see Lead Contamination in Drinking Water: Testing & Correction - Advice. More in-depth, un-biased, expert information on these topics and on building defect inspection, diagnosis, & repair can be found at "More Information below. © 2008 Daniel Friedman, All Rights Reserved. New York State License # 16000005303

• Health hazards from lead content in water
• Action Level for Lead in Water - allowable lead limits
• Variations in Lead Level vs. Testing Methods
• How to Reduce Lead Contamination in Drinking Water: how to test & correction lead in drinking water
• More Information on Lead and other Contaminants in Drinking Water, & Building Diagnostic Inspections and Repairs

Health hazards from lead content in water

Recently there was also a flurry of concern about lead contributed by brass in private well pumps. However the testing methods used for this latter topic misrepresented an exaggerated and frankly dubious risk. Finally, it is possible for lead to be found in private well water if lead contaminants have entered the local aquifer.

Action Level for Lead in Water - allowable lead limits

New York State Department of Health has set an action level of 0.015 mg/L of lead in a sample of water drawn from a tap used for drinking water after a 6-hour period of no water use.

Variations in Lead Level vs. Testing Methods

Lead levels will usually be quite high in water which has sat overnight in a lead line from street main to house.

Most lab tests indicate low lead levels in water from such lines after the test fixture has run until all standing water in the piping has been flushed out with fresh from the municipal supply mains in the street.

There are ambiguities in instructions offered by some municipalities about how to obtain a water sample for lead testing. The particulars of how the water sample is taken can make a big difference in the lead level obtained.

1. The very first draw of water from a fixture is measuring lead contributed by any lead-containing brass which is present in some faucets.
2. "First draw" taken after a moment of flushing out the faucet is taking water from the pipes near the fixture. Depending on pipe material and length, considerably more water might have to be taken before observing the water sample exposed to most lead uptake.
3. First cold water after a night of no usage is likely to provide water that was sitting in the entry main from street to house. If this line is lead, the lead content of this sample will be quite high. Alternatively, if all piping were visible between the test fixture and water meter (rarely the case) one could calculate the volume of water necessary to flush to obtain a sample from the line to the street.
4. A water sample taken after running the water for several minutes (depending on length of piping in the house from street to fixture) is sampling the quality of water provided by the municipality. Some city plumbing officials have expressed the opinion that lead oxide build-up in pipes insulates against significant lead levels in water actively running through such lines.

Most local building codes do not require removal of lead, for example, the City of Poughkeepsie Building Codes do not require removal of residential lead supply lines (house to street). However eventually (usually after 40-60 years) these lines corrode, leak, and have to be replaced. Replacing the main supply from street to the water meter, when required, could involve significant expense.

People with concerns for the amount of lead in water should consult the localhealth department and should have their water tested for lead. Typical lab fees are $20. to $25. per sample plus the cost of hiring an independent consultant to collect and handle the water sample if you don't do it yourself.

Even if you are not concerned with testing for lead in water it would be wise to reduce possible lead intake by flushing any lead-containing piping before drinking such water. In addition, lead-in-water removal equipment is available from water treatment companies.

Also see How to Reduce Lead Contamination in Drinking Water: how to test & correction lead in drinking water

Contents - More Water Testing & Building Inspection/Test Information Sources

Use links at the left of each page to navigate this document or to view other topics at this website. Green links at page left show where you are in our document or website.

More Information on Testing and Correcting Unsanitary Drinking Water & Building Diagnostic Inspections and Repairs

• How to Reduce Lead in Drinking Water
• Drinking Water testing, contamination, correction - all topics
• Drinking Water Testing Advice for home buyers home owners home inspectors
• Choices of Water Tests & Fees: A Summary of Types of Water Tests, Degrees of Comprehensive Water Testing, Details of Water Test Parameters
• Cheating on water tests: Testing Water for Real Estate Transactions - make sure your water test is valid
• General water testing and corrective measure advice: contact your local health department.
• Interpreting Drinking Water Test Results and Correcting Unsatisfactory Water
• Drinking Water Contaminant Levels - Maximum Allowed
• Drinking Water Contamination and Pollution How to Detect, Test, Correct, and Prevent Well Water Contamination - US EPA - Groundwater
• How to Reduce Lead Contamination in Drinking Water: how to test & correction lead in drinking water
• When and How to Shock or Chlorinate a Well - Procedure for Shocking a Well to (temporarily or maybe longer) "Correct" Bacterial Contamination
• Water and Waste Water Test Methods, US EPA
• Water Requirements, Home & Outdoor Living
• ATSDR: Nitrate/Nitrite Toxicity [Big, Slow-Loading File] U.S. Government ATSDR Science Corner - 2.5MB PDF
• Water Supply & Drain Piping, Wells, Pumps, Water Supply Equipmentt
• The Septic System Information Website - Extensive, Detailed Consumer and Industry Information on Septic System Inspection, Testing, Maintenance, Alternatives for on-site waste disposal
• Sewage or Septic contamination in buildings - Investigation, Testing and Remediation

InspectAPedia ^TM Home & Site Map - Building Inspection, Diagnosis, & Repair, Environmental Inspection & Testing - Research Website

The Mold Information Center: What to Do About Mold in Buildings, When and How to Inspect for Mold, Clean Up Mold, or Avoid Mold Problems

Use this simple, economical mold test kit by following our instructions on how to collect and mail mold samples to our lab

Environmental Inspection, Testing, & Diagnosis On-Site IAQ, Gas, Air Testing, Mold Investigation, Sick Building Diagnosis, Lab Services, & Remediation Plan Preparation - indoor air quality testing, problem source determination, supporting lab work, written remediation plan addressing removal of environmental and other hazards and prevention of their recurrence.

Home Inspection Construction Consulting Services & advice for home buyers

Contact Daniel Friedman for website content suggestions or for fee-paid consulting

	Enter your search terms Submit search form
	Search This Website - InspectAPedia.com